ozzymat
Trade Count:
( 0)
 Offline
Posts: 26
Location: South Australia
|
 |
« Reply #30 on: August 28, 2011, 05:25 AM » |
|
Solution A. without Mylar spine reinforcement.
If you have a look at the photos on Davide site you will notice only one run of zig zag stitching down the spine which suggest no Mylar spine.
What he does have are two small pieces of Mylar;
One which is the same shape as the Darcon lower spreader "T" reinforcement and sewn on the opposite side.
One small piece of mylar at the tail which I can only assume is required as the Darcon for the lower spreader "T"
does not run to the tail.
The plans and photos aren't clear on the nose so I used a piece of 50mm x 50mm Dacron folder in half to create a nose bag then put a piece of sports bag cut to the dimensions of the "Naso Invictus" circle on the plans to form the nose.
|
|
|
|
|
Logged
|
|
|
|
Untitled
Trade Count:
( 0)
Offline
Posts: 104
Location:
|
|
« Reply #31 on: September 07, 2011, 07:38 PM » |
|
A nylon Invictus  |
|
|
|
|
Logged
|
|
|
|
ko
Trade Count:
( +9)
 Online
Posts: 974
Location: hermosa beach CA
|
|
« Reply #32 on: September 07, 2011, 08:22 PM » |
|
hopefully will get to give this beauty a test drive tomorrow great looking kite marco. did you make annie a pink one??
|
|
|
|
|
Logged
|
have fun kurt
|
|
|
coogee
Trade Count:
( 0)
Offline
Posts: 231
Location: Sydney Australia
|
|
« Reply #33 on: September 08, 2011, 12:40 PM » |
|
That looks very good!
Mike
|
|
|
|
|
Logged
|
|
|
|
Stuart99
Trade Count:
( +2)
Offline
Posts: 78
Location: Richmond, VA
|
|
« Reply #34 on: September 21, 2011, 01:26 PM » |
|
Here is my finished Invictus UL. It flies a bit lower than I expected. I haven't had a real good chance to fly it as the wind has been non existent over the last week or so. The zero version my be on my build list   |
|
|
|
|
Logged
|
|
|
|
DWayne
Trade Count:
( +10)
Offline
Posts: 1356
Location: Corning, Ca.
|
|
« Reply #35 on: September 30, 2011, 01:27 AM » |
|
What software do I need to be able to see and/or print this plan?
Denny
|
|
|
|
|
Logged
|
I always wanted to be a procrastinator..........
I just never got around to it.
|
|
|
Ca Ike
Trade Count:
( +23)
Offline
Posts: 1510
Location: Stockton, CA
|
|
« Reply #36 on: September 30, 2011, 01:56 AM » |
|
What software do I need to be able to see and/or print this plan?
Denny
Pretty much any pdf viewer works |
|
|
|
|
Logged
|
|
|
|
DWayne
Trade Count:
( +10)
Offline
Posts: 1356
Location: Corning, Ca.
|
|
« Reply #37 on: September 30, 2011, 05:18 AM » |
|
What software do I need to be able to see and/or print this plan?
Denny
Pretty much any pdf viewer works Oh really? Denny |
|
|
|
|
Logged
|
I always wanted to be a procrastinator..........
I just never got around to it.
|
|
|
Ca Ike
Trade Count:
( +23)
Offline
Posts: 1510
Location: Stockton, CA
|
|
« Reply #38 on: September 30, 2011, 05:32 AM » |
|
Yep just make sure when you print you set it for 100% scale or even easier just take the file to a local printer.
|
|
|
|
|
Logged
|
|
|
|
DWayne
Trade Count:
( +10)
Offline
Posts: 1356
Location: Corning, Ca.
|
|
« Reply #39 on: September 30, 2011, 05:35 AM » |
|
I've tried 2 different PDF viewers and neither one would open the file.
Maybe because its a rar file?
Denny
|
|
|
|
|
Logged
|
I always wanted to be a procrastinator..........
I just never got around to it.
|
|
|
Ca Ike
Trade Count:
( +23)
Offline
Posts: 1510
Location: Stockton, CA
|
|
« Reply #40 on: September 30, 2011, 05:44 AM » |
|
RAR is just the compressed archive use win zip to extract it. IF you still can't get it check your e-mail I'll send you the files uncompressed.
|
|
|
|
|
Logged
|
|
|
|
DWayne
Trade Count:
( +10)
Offline
Posts: 1356
Location: Corning, Ca.
|
|
« Reply #41 on: September 30, 2011, 05:52 AM » |
|
Got it.  Thanks Anthony  Denny |
|
|
|
|
Logged
|
I always wanted to be a procrastinator..........
I just never got around to it.
|
|
|
DWayne
Trade Count:
( +10)
Offline
Posts: 1356
Location: Corning, Ca.
|
|
« Reply #42 on: October 12, 2011, 04:23 AM » |
|
With a little help from my friends I got the plan printed.  Now its time for some gluing and sewing. Denny |
|
|
|
« Last Edit: October 12, 2011, 04:25 AM by DWayne »
|
Logged
|
I always wanted to be a procrastinator..........
I just never got around to it.
|
|
|
Dolphinboy
Trade Count:
( +15)
Offline
Posts: 617
Location: Grants Pass, OR
|
|
« Reply #43 on: October 12, 2011, 09:40 AM » |
|
Denny, I'll have to come by and try it when you get is finished I love the videos of this kite. |
|
|
|
|
Logged
|
|
|
|
DWayne
Trade Count:
( +10)
Offline
Posts: 1356
Location: Corning, Ca.
|
|
« Reply #44 on: October 12, 2011, 12:10 PM » |
|
Denny, I'll have to come by and try it when you get is finished I love the videos of this kite. It would be a pleasure to fly with you again James. I'll post a picture when they're done. You're welcome to fly them anytime. Denny |
|
|
|
|
Logged
|
I always wanted to be a procrastinator..........
I just never got around to it.
|
|
|
|
