GWTW Forum
May 22, 2019, 04:38 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: With regrets ... the Forum is closing permanently on JUNE 8th
to contact us email: kitekid@gmail.com
 
   Home   Help Forum Info Login Register Chat  
Pages: [1]   Go Down
  Print  
Author Topic: Frame details of Le Quartz  (Read 3356 times)
0 Members and 1 Guest are viewing this topic.
Ara Ararauna
Trade Count: (0)
****
Offline Offline

Posts: 938

Location: Sant Cugat (Barcelona)

« on: December 26, 2012, 03:31 PM »

Hi,

I haven't been able to find the folliwing info about the frame of the Le Quartz kite:

1. What is the distance from the nose at which the central-T be placed?
2. At which distances are the inner and outer stand-off connectors placed from the central-T?
3. For the central-T I don't really understand which type of garden hose they suggest because I have found none that are 6mm internal diameter... So I am planning on placing C connectors above and below the central-T to hold it in place. Would that work?

I would appreciate some help since I'm in the final building steps 

Cheers.
Logged

In my bag...
Duals: NoName (NoBrand), Nexus (Prism), Soul (Flying Wings), Talon UL (JoE), LeQuartz (own build), Illusion Classic (Prism), Aura SUL custom (Skyburner), Sixth Sense STD (Krijn)
Singles: Conyne STD (my design)
Wayner
Trade Count: (+18)
*****
Offline Offline

Posts: 1243


Location: Las Vegas, NV

« Reply #1 on: December 26, 2012, 04:07 PM »


I'm in the final building steps 


Ara,
Can't help with your questions, but I looking forward to your finished kite.  Grin
Logged
sugarbaker
Trade Count: (+10)
****
Offline Offline

Posts: 878


Location: Rocklin, CA

« Reply #2 on: December 26, 2012, 10:32 PM »

Center T from nose can be figured on the kite... Place the spine in the sail and mark where the center T opening hits the spine.  C clips will work fine, jus leave a space big enough for the bridle to fit between the t piece and the c clip.

As for standoff connector placement, this can also be figured when assembling the kite.  When assembled, the standoffish should be 90 degrees to the lower spreader. 
Logged
Ara Ararauna
Trade Count: (0)
****
Offline Offline

Posts: 938

Location: Sant Cugat (Barcelona)

« Reply #3 on: December 27, 2012, 12:42 AM »

Ok, thanks.

But the T opening is quite long. Are we safe if we say that the position for the central T is that in which it naturally falls when everything is set up? Or should the T be forced a little further up or down to somehow "bend" the LSs?

Logged

In my bag...
Duals: NoName (NoBrand), Nexus (Prism), Soul (Flying Wings), Talon UL (JoE), LeQuartz (own build), Illusion Classic (Prism), Aura SUL custom (Skyburner), Sixth Sense STD (Krijn)
Singles: Conyne STD (my design)
sugarbaker
Trade Count: (+10)
****
Offline Offline

Posts: 878


Location: Rocklin, CA

« Reply #4 on: December 27, 2012, 10:44 AM »

I would shoot for the center of the cutout... Some bend in the lower spreaders is good, I would shoot for this in order to keep tension on the sail and leading edge connectors (so the spreaders are less prone to popping out.)
Logged
Ara Ararauna
Trade Count: (0)
****
Offline Offline

Posts: 938

Location: Sant Cugat (Barcelona)

« Reply #5 on: December 27, 2012, 11:24 AM »

Great! Got it.
Tomorrow I'll have finished the bridle and then I'll be able to go out, take some pictures to show you the kite and hopefuly do the maiden flight!
I'm so nervous...   Huh
Logged

In my bag...
Duals: NoName (NoBrand), Nexus (Prism), Soul (Flying Wings), Talon UL (JoE), LeQuartz (own build), Illusion Classic (Prism), Aura SUL custom (Skyburner), Sixth Sense STD (Krijn)
Singles: Conyne STD (my design)
sugarbaker
Trade Count: (+10)
****
Offline Offline

Posts: 878


Location: Rocklin, CA

« Reply #6 on: December 27, 2012, 11:30 AM »

I'm sure it will be wonderful.  It exciting to pilot your first sport kite build.
Logged
Ara Ararauna
Trade Count: (0)
****
Offline Offline

Posts: 938

Location: Sant Cugat (Barcelona)

« Reply #7 on: December 27, 2012, 02:07 PM »

Ah! The last question that I now have...

How much weight should I put on the bottom tip of the spine?

The instructions are not too clear, but I seem to understand that it should be 10grams.

Is that correct?

Thanks
Logged

In my bag...
Duals: NoName (NoBrand), Nexus (Prism), Soul (Flying Wings), Talon UL (JoE), LeQuartz (own build), Illusion Classic (Prism), Aura SUL custom (Skyburner), Sixth Sense STD (Krijn)
Singles: Conyne STD (my design)
Pages: [1]   Go Up
  Print  
 
Jump to:  


Powered by MySQL Powered by PHP Powered by SMF 1.1.8 | SMF © 2006-2008, Simple Machines LLC
SimplePortal 2.2.1 © 2008-2009
Valid XHTML 1.0! Valid CSS!